







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Why Pasadena Homeowners Choose Cover Construction
We provide independent Cover construction service in Pasadena, handling the flat-packed cabinet assembly, frameless box alignment, and template-based quartz fitting that make a Cover kitchen or bath package work in an older home. What sets our Cover work apart is field reality: we assume the walls are out of plumb, the floor has a low spot, and the existing plumbing stub-outs won’t match the new fixture bundle, because in Pasadena’s housing stock they usually don’t. Our technicians have up to 12 years of experience assembling and installing flat-pack cabinet systems, and we bring that to every Cover job.
To be clear: Construction Pasadena is an independent service provider. We are not affiliated with, authorized by, or endorsed by Cover. We repair, install, and service Cover products using quality parts that fit them. If you have a flat-pack order arriving or a half-assembled run sitting in your kitchen, call (844) 905-4587. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
Why Trust Construction Pasadena for Your Cover Construction?

Cover cabinets arrive as boxes of panels, cam locks, dowels, and hinges. The instructions get you a cabinet-shaped object. What they don’t tell you is what to do when your 1915 Craftsman wall bows a half inch over the run, or when a cam lock strips because the box went together on an uneven floor. That’s the part we handle.
We’ve assembled and installed Cover kitchen and bath packages in homes across Pasadena, and the pattern is consistent. The proprietary cam-lock and dowel hardware needs careful, square assembly or doors and drawers misalign the moment weight goes in. Frameless runs show every bit of wall variance through the door reveals. Template-based counters assume a straight wall that older homes rarely have. We plan for all three before we touch a panel.
Warranty-safe practice matters here. Forcing a box square with fasteners, trimming a counter without sealing the cut edge, or cross-threading a valve body during rough-in can void the warranty on that component. We assemble to spec, adjust at the hinges and levelers where adjustment belongs, and re-work the site rather than the product. Quality parts that fit Cover equipment, installed the way the manufacturer intended, keeps your coverage intact.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Common Cover Construction Problems We Fix in Pasadena
These are the issues we see most often with flat-packed Cover packages in Pasadena homes. None of them are product defects. They’re assembly and site-fit problems, and most are fixable without replacing anything.
- Doors and drawers misalign after assembly. Cam locks and dowels loosen or strip when a box is assembled without a square reference and a flat surface. Once the box racks even slightly, the door plane shifts and drawers bind in the opening. Re-squaring, replacing compromised cam hardware, and resetting hinges usually restores even reveals.
- Uneven reveal gaps along a frameless run. Frameless cabinets have no face frame to hide wall variance, so an out-of-plumb Pasadena wall shows up directly as tapering gaps between doors and gapping at the ceiling or floor. Shimming the run to the wall and scribing filler where needed closes those gaps cleanly.
- Quartz counters and backsplash panels that don’t land. Factory templates are cut to nominal dimensions, not to your wall’s bow. In older homes the counter needs re-cutting at an end return or the seam needs adjusting on site before the panel sits flush and the backsplash meets the counter without a wedge of caulk.
- Shower valve and drain rough-in mismatches. Cover fixture bundles carry their own rough-in dimensions. When an existing tub alcove has stub-outs set for the old valve, the new trim won’t seat without adapter work or re-working the stub-out. Forcing it cross-threads the body and creates a leak behind the wall.
- Water damage at sink bases and toe kicks. Flat-pack panel construction is vulnerable where a slow supply leak or a failed drain gasket goes unnoticed. Swollen box panels and delaminated toe kicks are the one case where repair stops making sense and replacement of that cabinet is the right call.
Cover Parts & Our Repair-vs-Replace Approach

We don’t stock Cover parts, and we don’t claim to. What we do is source correctly: Cover’s own replacement doors, drawer fronts, hinges, and cam hardware when finish match and the warranty on that part matter, and quality aftermarket soft-close hinges or leg levelers where they genuinely outperform the stock hardware. Usually the stock hardware is fine once it’s installed square.
The repair-or-replace call comes down to two questions. Are the boxes structurally sound? And does the layout still fit the room? A racked but intact cabinet run can be re-squared, re-shimmed, and re-hinged for a fraction of replacement. Water-swollen boxes, delaminated panels, or a layout that no longer works with the room ends the conversation and replacement becomes the honest answer. We’ll tell you which one you’re looking at before any work starts, and the written estimate sets the final price. Call (844) 905-4587 for a free estimate.
Our Cover Service Process – Step by Step
- 1
Diagnosis. We check the assembled boxes for square, inspect cam locks and dowels for stripping, measure wall plumb and floor level along the run, and verify existing plumbing rough-in dimensions against the Cover fixture bundle. This is where we find out whether the problem is assembly or site.
- 2
Repair or install. For a new package, we assemble on a flat surface with a square reference, shim the run to the wall, and scribe fillers to close the gaps the frameless boxes expose. For an existing installation, we re-square, replace compromised hardware, and reset hinges and levelers. Counters get trial-fitted and re-cut on site before anything is permanent.
- 3
Test. Doors and drawers get cycled through full travel for rubbing or binding. Reveals get checked for even spacing across the run. Every valve, drain, and supply connection gets pressure-tested and checked for weeps before the wall closes or the counter goes down.
- 4
Warranty. We document what was assembled, what was adjusted, and what was replaced, so the parts and workmanship record is clear. Adjustments stay within what the product’s warranty allows, and we tell you plainly if a repair you’re considering would compromise coverage on a component.
See the difference
Before
After
Before
After
Before
AfterCover Products We Service & Install in Pasadena

We work across the Cover product range for kitchens and baths, and we know where each one tends to need field attention in an older Pasadena home.
- Semi-custom kitchen cabinet packages, frameless with flat-packed boxes and doors
- Bathroom vanity and linen cabinet sets
- Quartz and solid-surface countertops and backsplash panels
- Shower and bath fixture bundles, including faucets, showerheads, and drains
The most common sub-services for Cover owners are cabinet installation and refacing, full kitchen remodeling, and tub-to-shower conversion. Each one involves the same core skill: getting a precision-manufactured flat-pack system to fit a house that was never built to precision. In Pasadena’s pre-1950 housing stock, that’s the whole job.
We Also Service These Brands
Cover is one path, not the only one. We also install and work with KraftMaid and Wellborn cabinetry, Cambria, Caesarstone, and Silestone quartz surfaces, and Kohler, Moen, Delta, Grohe, American Standard, Toto, and Blanco fixtures. If your project mixes a Cover package with another brand, or you’re still deciding which cabinet line fits your budget and layout, we can talk through both. Brands you can look up before you commit.
FAQs – Cover Construction Service in Pasadena
Yes. Assembling and installing a flat-packed Cover order doesn’t require brand authorization. It requires square assembly, correct hardware handling, and site-fitting to your walls and floor. We do all three as an independent installer. Call (844) 905-4587 for a free estimate.
Rubbing doors almost always trace back to a box assembled out of square or cam locks that stripped during assembly. When a box racks, the door plane shifts and the hinge side no longer sits parallel to the opening. Re-squaring the box, replacing stripped cam hardware, and adjusting the hinges resolves it in most cases without replacing any part.
Often not without some on-site work. Factory templates are cut to nominal dimensions, and older Pasadena homes have wall bow and out-of-square corners that a template can’t account for. The usual fix is re-cutting an end return or adjusting a seam during fitting. Typical countertop installation runs $2,000 – $6,500, and the written estimate sets the final price. Call (844) 905-4587 and we’ll look at yours.
Usually, but the rough-in has to be checked first. Cover valve and drain dimensions don’t always match existing stub-outs, so adapter work or re-working the stub-out is often needed before the trim will seat properly. Forcing the trim risks cross-threading and a hidden leak. Tub-to-shower conversion typically runs $3,500 – $10,000, with the written estimate setting the final price. Call (844) 905-4587 for a free estimate.
Repair is usually worth it when the boxes are intact. Re-squaring, re-shimming, and re-hinging an assembled run costs far less than replacement and preserves the finish you paid for. Replacement makes sense when boxes are water-swollen, panels are delaminated, or the layout no longer fits the room. Cabinet installation typically runs $4,000 – $13,000 when replacement is the answer. Call (844) 905-4587 to talk it through – estimates are free.
It depends on scope. A single cabinet run is a different project from a full kitchen. Here are typical estimated ranges for the work Cover owners most often ask about. The written estimate sets the final price.
| Service | Typical Estimated Range |
|---|---|
| Full Kitchen Remodeling | $14,000 – $45,000 |
| Small Kitchen Remodel | $9,000 – $20,000 |
| Cabinet Installation | $4,000 – $13,000 |
| Countertop Installation | $2,000 – $6,500 |
| Kitchen Island Installation | $3,000 – $10,000 |
| Tub-to-Shower Conversion | $3,500 – $10,000 |
| Walk-In Shower Installation | $4,500 – $12,000 |
| Bathroom Vanity Installation | $800 – $3,000 |
Call (844) 905-4587 for an exact quote – estimates are free.
Book Your Cover Service in Pasadena, CA
Whether it’s a flat-pack order waiting to be assembled, a cabinet run that needs re-squaring, or a shower conversion where the rough-in doesn’t line up, we’ll give you a straight answer on what the job involves. Call (844) 905-4587 for a free estimate. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Construction Pasadena.












