







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Why Pasadena Homeowners Choose Mr-Glass Construction
We provide independent Mr-Glass construction and glass service in Pasadena: frameless and semi-frameless shower enclosures, custom mirror and glass panels, glass railings, and interior partitions. We’re upfront about one thing: Construction Pasadena is an independent service provider, not a Mr-Glass dealer, and we’re not affiliated with or authorized by the manufacturer. What sets our Mr-Glass work apart is diagnosis before a quote. We know how these enclosures are sized, sealed, and anchored, so we can tell you whether a leak is a worn sweep or a hinge that’s pulled loose from the wall behind the tile.
Pasadena’s housing stock makes that judgment matter. From 1900s-1920s Craftsman bungalows in Bungalow Heaven and the historic districts near Orange Grove Boulevard to mid-century homes on the east side, bathrooms here were rarely plumb and square when glass went in. Plenty of pre-1950 homes still carry the quirks that come with a century of small remodels, which is where enclosure problems usually start.
Call (844) 905-4587. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Why Trust Construction Pasadena for Your Mr-Glass Construction?

Our technicians have up to 12 years of experience, and a good share of that has gone into glazing and enclosure work where panel sizing and hardware fit aren’t forgiving. A frameless door hung in 1/2″ tempered glass weighs far more than people expect. If the hinge geometry doesn’t match the panel thickness Mr-Glass builds to, the door sags, the strike side drifts, and the seal line never sits right. So we match the hardware to the glass the enclosure actually uses instead of forcing a generic kit onto it.
Our credibility rests on knowing Mr-Glass panel sizing, seal systems, and hardware families well enough to do three things accurately: diagnose the real fault, recommend repair or replacement honestly, and do the work in a way that respects your warranty. That means using parts that fit correctly, anchoring hinges into solid material, and avoiding improvised fixes that could give a manufacturer a reason to refuse a claim later.
Because Mr-Glass enclosures run into the same installation conditions across Pasadena, we’ve learned to check the things that fail first on a second visit: plumb walls, hinge blocking, and drainage slope. The parts are only half the job. The other half is the wall they mount to, and in a Pasadena bathroom, that wall is often a century of decisions stacked on top of each other.
One more point worth being clear about. We’re not factory-trained or certified by Mr-Glass, and we never present ourselves that way. We’re an independent shop that works confidently with these enclosures and glass products. The written estimate sets the final price, and there’s no charge for the estimate itself.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Common Mr-Glass Construction Problems We Fix in Pasadena
Most Mr-Glass service calls land on five faults. Knowing which one you’re looking at saves money, because two of them are hardware problems and one of them looks like a cleaning problem but is really surface damage.
- Leaks at the bottom sweep and vertical seal on frameless hinged enclosures. Sweep gaskets harden and shrink with age and heat, and when they pull away from the glass, water walks out under the door. The sweep is usually the affordable fix, but only if the door itself is hanging square. If it isn’t, a new sweep will leak within a season.
- Door sag and hinge binding on heavy 1/2″ frameless doors. The cause is almost always anchoring. When hinges are set into tile over backer board instead of solid blocking, the mounting points loosen under the weight of a thick tempered panel, and the door drops out of alignment. Hinge screws that won’t stay tight are a sign of missing blocking, not failing hardware.
- Hard-water mineral etching and haze. Pasadena’s dry inland climate makes this one common. Etched glass looks dirty no matter how often you clean it, but the cloudiness is surface damage, not film. Once minerals bond to the glass, polishing can improve the look, though it rarely restores it. This is the most frequently misdiagnosed Mr-Glass problem we see, and the most expensive to ignore for years.
- Out-of-square panel gaps and popping rollers on semi-frameless sliders. Sliders are tolerant of a small amount of variation, and they tell you when the opening has shifted. Rollers that climb out of the track and a widening gap along one edge usually trace to a wall or header that moved after the original install. New rollers won’t fix an opening that’s no longer square.
- Chipped glass around the hinge cutouts and panel edges. Thick tempered glass can chip at cutouts and edges, and a small chip near hardware weakens the panel exactly where load concentrates. Small chips aren’t always reason to replace, but a chip at a hinge cutout on a door is worth a look before it becomes a break.
Mr-Glass Parts & Our Repair-vs-Replace Approach

We use OEM-grade Mr-Glass-compatible sweeps, seals, hinges, and rollers wherever panel dimensions demand an exact fit, and quality aftermarket hardware only for non-critical trim. We don’t claim to stock genuine Mr-Glass parts. What we do claim is knowing which parts need a precise match and which don’t, so the hardware budget goes where it matters. A sweep that fits badly leaks. A hinge that fits badly sags. Those are the parts worth getting right.
Repair makes sense when the glass is sound and the problem is hardware, seals, or anchoring. Replacement is the honest call when glass is chipped at a cutout, badly etched, or the panel has gone out of square with the enclosure. Repeated hardware swaps on failing glass just spend money twice.
Call (844) 905-4587 for a free estimate. We’ll tell you which side of that line your enclosure is on before you commit to anything.
Our Mr-Glass Service Process – Step by Step
- 1
Diagnosis. We check the door for plumb, verify the opening is square, look at what the hinges are actually anchored into, and examine the glass edge and surface. On a leak, we identify whether it’s the sweep, the vertical seal, the door alignment, or water escaping behind the frame.
- 2
Repair or install. For a repair, we reset or replace the hinges with compatible hardware and install new sweeps and seals. For a new Mr-Glass enclosure, we confirm panel sizing before ordering, then set blocking or verify anchoring so the weight of thick tempered glass has something solid to hang from.
- 3
Test. We run water against the door, open and close it through its full arc, and check the seal line along the bottom and sides. An enclosure that passes the eye test and fails the water test isn’t finished.
- 4
Warranty. We go over what the manufacturer’s warranty covers versus what our workmanship covers, so nothing about future service comes as a surprise if a hinge loosens or a sweep fails.
That order matters. Skipping diagnosis is why some enclosures get a third set of rollers bolted onto an opening that was never square.
Mr-Glass Products We Service & Install in Pasadena

Frameless Glass Shower Enclosures top the list, including the hinged doors and fixed panels in 3/8″ and 1/2″ tempered glass that make up most Mr-Glass shower work in Pasadena. We handle Walk-In Shower Installation, where the opening and slope get planned before the glass is ordered. We also do Tub-to-Shower Conversion, swapping a tub and its surround for a walk-in shower finished with a Mr-Glass enclosure, which is the scope most Pasadena owners ask about when reclaiming a small bathroom.
Beyond the shower, we service semi-frameless sliding door systems, custom-cut mirror and glass panels, and glass railing and interior partition systems. Each of those has its own failure pattern and its own fit requirements.
What a typical Mr-Glass shower call usually involves
A common Mr-Glass call involves a frameless hinged shower door that no longer closes flush and leaks at the bottom corner. The usual cause: hinge screws have loosened from insufficient blocking behind the tile, and the heavy 1/2″ panel has shifted out of plumb. A qualified local pro typically pulls the door, verifies the opening is square and the wall has solid anchoring, re-sets or replaces the hinges with OEM-compatible hardware, and installs new sweeps and vertical seals. If the glass itself is chipped at the hinge cutout or badly etched from hard water, the realistic answer becomes a new panel or full enclosure rather than more hardware adjustments.
See the difference
Before
After
Before
After
Before
AfterWe Also Service These Brands
Pasadena projects often touch more than one trade. A bathroom with a Mr-Glass enclosure may also get vanity cabinetry from KraftMaid, quartz surfaces from Cambria or Silestone, and fixtures from Kohler, all under one project relationship. Owning several service lines means fewer vendors to chase and one accountable contractor for the scope. The point is material continuity and a schedule that holds.
Typical Mr-Glass Construction Costs in Pasadena
These are typical estimated ranges for shower and enclosure work in Pasadena. The written estimate sets the final price.
| Service | Typical Estimated Range |
|---|---|
| Walk-In Shower Installation | $4,500 – $12,000 |
| Tub-to-Shower Conversion | $3,500 – $10,000 |
| Shower Replacement | $3,000 – $8,500 |
| Small Bathroom Remodel | $5,000 – $12,000 |
| Bathroom Remodel | $9,000 – $28,000 |
In the historic districts, one condition pushes the number up before any material is chosen. Within Bungalow Heaven, Prospect Park, and the city’s other historic overlays, even work as small as a shower rebuild or window replacement can trigger design review and a Certificate of Appropriateness from the Design Commission. That extra design-review time is something neighbors like Arcadia or Monrovia largely avoid, and it’s worth budgeting for up front rather than discovering mid-project.
Call (844) 905-4587 for a free estimate and a quote that accounts for what’s actually behind the tile.
FAQs – Mr-Glass Construction Service in Pasadena
No. We’re an independent Mr-Glass service provider and not a Mr-Glass dealer, and we’re not affiliated with or authorized by the manufacturer. We service and install Mr-Glass glass products using hardware that fits them, and we’re clear about that boundary in every estimate. If a manufacturer-warranty claim is part of your situation, we’ll tell you what you need to pursue it directly.
Yes. We use OEM-grade Mr-Glass-compatible sweeps, seals, hinges, and rollers where the panel dimensions demand an exact fit, and quality aftermarket hardware only for non-critical trim. We don’t claim to stock genuine Mr-Glass parts. Fit is what matters on a shower enclosure, and a part that fits badly fails quickly regardless of the label on it.
A hardware repair like new sweeps, seals, or a hinge reset usually takes a single visit. New enclosure installs and tub-to-shower conversions take longer because of panel ordering and, in some cases, wall work behind the glass. In Pasadena’s historic districts, add design-review time on top of the install if your project needs a Certificate of Appropriateness. We’ll give you a realistic window with the written estimate.
We cover frameless hinged shower enclosures in 3/8″ and 1/2″ tempered glass, semi-frameless sliding shower systems, custom-cut mirror and glass panels, and glass railing and interior partition systems. For showers, that means everything from a leaking door fix to full walk-in shower installation and tub-to-shower conversion with a Mr-Glass enclosure.
It doesn’t have to. Service performed with parts that fit and anchoring done to the manufacturer’s specifications is how you stay on the right side of a warranty. Improvised hardware, silicone used to hide a bad seal, or hinges sunk into tile without blocking can create problems later. We work with the fit requirements in mind and walk you through what your warranty covers before we start.
Typical estimated ranges in Pasadena run $3,000 – $8,500 for shower replacement, $3,500 – $10,000 for a tub-to-shower conversion, and $4,500 – $12,000 for walk-in shower installation, with full bathroom remodels estimated at $9,000 – $28,000. On the FAQ questions above: My Mr-Glass frameless shower door is leaking at the bottom corner even after I replaced the sweep – what’s actually wrong? The sweep wasn’t the root cause. When a door leaks at the bottom corner after a sweep swap, the door itself is usually hanging out of plumb because the hinge mounting has loosened behind the tile, so water runs to the low corner no matter how new the seal is. Can a chipped Mr-Glass shower panel be repaired, or does the whole enclosure need replacing? A chip at a hinge cutout usually means replacing the panel, because tempered glass can’t be reliably repaired where load concentrates. Why does my Mr-Glass glass look permanently cloudy no matter how I clean it? The haze is mineral etching from hard water, surface damage rather than film, so cleaning can’t remove it. Is a tub-to-shower conversion with a Mr-Glass enclosure feasible without moving the drain? Often yes, and the drain location is one of the first things we check at the estimate. My Mr-Glass sliding shower door rollers keep popping out of the track – repair or replace? New rollers help only if the opening is square; if the header shifted, the track is the real problem. Call (844) 905-4587 for an exact quote on your Pasadena project – estimates are free.
Book Your Mr-Glass Service in Pasadena, CA
If your Mr-Glass enclosure is leaking, the door won’t close flush, or the glass has gone cloudy, call (844) 905-4587. We’re an independent provider with no charge for the estimate, and we’ll tell you plainly whether a repair or a replacement is the honest answer. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday, closed Saturday. Estimates are free, the price is set per job by the written estimate, and our workmanship is covered.
Written by the team at Construction Pasadena.












